1、在室內裝飾工程的施工作業中多數情況下是大量工種混合作業，大量的施工人員或裝飾物資的移動會磨損或腐蝕石材表面，嚴重時會造成石材大面積污損，無法達到施工合同交付標準；當然有時也會因為鋪裝人員手藝不精，鋪設完成后參差不齊或有剪刀差，這時就需要對進行石材翻新處理。 2、石材經過長期使用，即使保養得當也會因為合理的磨損而失去原有的光澤；如果二次完整裝修，石材地板一般不需要更換，只需要進行相對簡單的翻新拋光處理，就會得到全新的效果。 3、填縫處理：石材鋪設好后，在已鋪設好的石板相鄰間隙中以石材顏色近似的云石膠予以填隙處理，再用打磨機進行研磨、拋光處理。經由這種方式處理過后，石板會呈現整體沒被分割的美感，還可以減少石材發生水漬的機會。石材的許多病癥都是從石材相鄰間隙中開始，如果采用了無縫處理還會降低石材各種病癥的發生。 花崗巖和大理石等石材翻新流程 1、修補破損及中縫補膠：首先將石材原有破損的表面用接近石材顏色的云石膠進行填補。然后使用專用的石材開縫機對原來石材安裝的中縫重新整齊切割開縫，使縫隙的寬度變的差不多，再用接近石材顏色的云石膠對其進行填補。（注：若以前已經做過中縫處理則無需重新開縫） 2、剪口位打磨：使用花崗巖翻新機配合專用剪口研磨片對剪口位進行精心打磨，使其與石材翻新成為一個平面整體。 3、研磨拋光：使用專業的花崗巖拋光機，從石材水磨片由粗到細對石材進行研磨，致使地面光亮平整如新。 1, in the construction of interior decoration engineering in most cases is a large number of types of mixed operation, a large number of mobile construction personnel or decoration materials will wear or corrosion of the stone surface, can cause severe stone large area fouling, can not achieve the construction contract delivery standards; of course, sometimes because of survey personnel craft is not fine, laying is completed after uneven or scissors, then you need to deal with stone renovation. 2, after long-term use of stone, even if it is properly maintained, it will lose its original luster due to reasonable wear. If two times of complete decoration, stone floors generally need not be replaced, and only need relatively simple renovation and polishing process, it will get a new effect. 3, filling processing: Stone paved with stone, the approximate color in the adjacent stone clearance has been paved by marble glue to interstitial treatment, then grinding machine for grinding and polishing processing. After being treated in this way, the slab will show an overall aesthetic feeling that is not divided, and can also reduce the chance of water stains in the stone. Many diseases of stone are started from the adjacent space of stone, and it can also reduce the occurrence of various diseases of stone if they are treated with seamless treatment. Granite and marble renovation process 1, repair damaged and darn glue: first will damage the surface of the original stone fill stone with the color of marble near glue. Then use the slot machine dedicated to the original stone stone installation of the raphe re neatly cut slot, make the width of gap becomes almost, and close to the stone color on the marble glue to fill. (Note: if there has been a middle seam before, there is no need to re open the seam) 2, the cutting position is polished: using granite refurbishing machine to cooperate with the special shear grinder to carefully cut the cutting place, and make it become a whole with the stone renovation. 3, the use of granite polishing machine polishing: professional, stone tablets from the mill from coarse to fine grinding stone on the ground, smooth and bright as new.